Dryer vent cleaning
Whole-home duct cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Nikro Dryer Vent Cleaning in San Antonio: What to Know First
If you own a Nikro dryer vent cleaning system in San Antonio, we provide independent service, inspection, and repair for your equipment. Most Nikro jobs in our area are completed within one visit, and we give you a written price before any work begins, so you know the cost before we open a single panel. This page is for homeowners and property managers who run Nikro equipment in San Antonio and need someone who actually knows how these machines work when they need service. Call (430) 233-7681 for a free estimate.
How Nikro Products Fail – and How We Fix Them
- Nikro NS-Series Soot Vacuum motors lose suction when the pre-filter loads up with fine lint dust. The NS-2 and NS-3 models used by many San Antonio chimney and vent companies have a cloth pre-filter that catches what the HEPA misses. Once that filter cakes over, the motor works harder and pulls less. We pull the filter, knock out the loose debris, and wash or replace it depending on condition. A clean pre-filter usually restores full suction on the first pass.
- Nikro VAC-2 and VAC-3 dryer vent kits develop split hoses at the cuff connections. The rubber cuffs where the hose meets the machine take the brunt of every job. San Antonio heat dries out those cuffs faster than in cooler climates, and once they crack, you lose negative pressure at the vent opening. We replace cuffs and hose sections with quality aftermarket parts that match Nikro’s OD specs, so the connection stays tight.
- Nikro PRS Power Rod Systems bind up when lint packs into the rod couplings. The PRS-4 and PRS-6 rod sets are solid workhorses, but the quick-connect couplings collect lint dust that hardens with moisture. When a rod won’t seat fully, the whole system flexes and the brush head wanders off-center in the vent run. We disassemble, clean each coupling with a dry brush, and re-lubricate the threads with a dry graphite spray that won’t attract new lint.
- Nikro HEPA filter canisters leak at the gasket on older NS units. The gasket between the canister and the motor body flattens over time, especially in unconditioned San Antonio garages where temperatures swing hard. A leaking gasket means the machine recirculates fine dust instead of trapping it. We replace the gasket as a preventive step on any Nikro service call where the unit is more than a few years old.
- Nikro brush heads wear down on long vent runs common in Alamo Heights ranch-style homes. The nylon bristles on the standard 4-inch brush head flatten after repeated passes through long, multi-turn dryer vents. A worn brush skims the duct walls instead of scouring them. We keep replacement brush heads in the truck and swap them when the bristles show visible flattening, which saves you a second service call later.
Styles & brands we work with
Our Nikro Dryer Vent Cleaning Process
- 1
We open the machine and look at the filters first. Before we touch a vent, we check the pre-filter, HEPA canister, and hose connections on your Nikro unit. If the machine can’t pull proper negative pressure, cleaning the vent is wasted work.
- 2
We run a static pressure check at the vent opening. This tells us how much resistance is in the run before we start. Long San Antonio vent runs with multiple elbows show up here.
- 3
We clean from the dryer side out using your Nikro system or ours. If your machine is down, we bring our own Nikro and Rotobrush equipment and keep the job moving.
- 4
We inspect the full run with a camera after cleaning. You see what we see. We walk you through the footage before we pack up, so there’s no question about whether the job got done.
- 5
We document the work and give you a written report. Photos, before and after, included. Your invoice matches the written price you approved before we started.
- 6
We stand behind the work for 365 days. If the vent isn’t right, we come back and make it right. That’s the 365-Day Done Right Promise, in writing on every job.
See the difference
Before
After
Before
After
Before
AfterWhat Nikro Dryer Vent Cleaning Costs in San Antonio
Most Nikro dryer vent cleaning jobs in San Antonio run between $140 and $260 for a standard single-family home. If your Nikro unit needs parts like a pre-filter, hose cuff, or brush head, expect to add $35 to $120 depending on what’s worn out. Full overhauls on older NS units with a new gasket, filters, and hose set typically land between $300 and $450. What moves the price is vent run length, access difficulty, and how long since the last cleaning. We give you one flat price before work starts, so the invoice never surprises you. Call (430) 233-7681 for an exact quote. Estimates are free.
Why San Antonio Homeowners Call Linden Air Duct San Antonio for Nikro Work
We’ve served San Antonio homeowners since 2004, and we’ve pulled a lot of strange things out of dryer vents over the years. What matters more is what happens before the work starts. You know the tech’s name and face before they arrive, because we send a photo and show a photo ID badge at the door. Every tech is background-checked and identity-verified under The Threshold Standard. If your Nikro machine is down and your dryer vent is clogged, we also work on Lennox, Trane, and Carrier systems, so we can handle the full job in one visit. One call, one crew, one written price. Tell me what you’re seeing, and I’ll tell you whether it’s worth fixing. Marcus Veale built this company on that conversation.
FAQs
No. Dryer vent cleaning does not void your Nikro warranty, and we perform all work with OEM-spec filters and parts to keep your equipment within manufacturer tolerances. As an independent Nikro service provider, we’re not authorized by Nikro, but we follow their service guidelines closely because it keeps your machine running right.
In San Antonio, we recommend every 12 to 18 months for a standard home, and every 6 to 12 months if you have a long vent run, multiple turns, or a household that runs the dryer daily. South Texas humidity plus clay-heavy soil means lint clings and compacts faster here than in drier regions.
In most cases, yes. We stock common Nikro replacement parts on the truck, including pre-filters, HEPA gaskets, hose cuffs, and brush heads. If your machine needs a part we don’t carry, we’ll clean your vent with our own Nikro equipment and order the part for a follow-up visit.
That symptom almost always points to a loaded pre-filter. Fine lint dust packs into the cloth filter and chokes airflow, especially on long runs in older San Antonio homes. A quick filter clean or replacement typically restores full suction in minutes. Call (430) 233-7681 and we’ll walk you through it.
We show you camera footage of the full vent run before we leave, and we give you before-and-after photos in writing. If the vent isn’t right, the 365-Day Done Right Promise means we come back and correct it at no charge. That’s the standard, and it’s on every invoice.
Written by Marcus Veale, Owner, Linden Air Duct San Antonio at Linden Air Duct San Antonio, serving San Antonio and nearby areas.